Wodschow RN10 VL-2 Operations Instructions download pdf (Page 2)

Contents:

General:

In case of complaints, please contact your supplier.

The guarantee does not cover faults resulting from faulty op-

eration, overloading and lacking observance of directions of

maintenance.

It should be checked that all loose parts are delivered with the

mixer such as bowl, tools and intermediate pieces.

To the attachment drive should only be connected attachments

produced by A/S WODSCHOW & CO.

safety:

If the mixer is not connected to earth

there is danger of injury.

It must be ensured that the cable used

for connecting the machine to power,

meets the standard of the country

where the machine is installed! – see

also “Connection to power”

The constant noise level of the work place of the operator

is lower than 70 dB (A).

The mixer is designed for manufacture of pro ducts

which do not during processing cause reactions

or emit substances which may be detrimental to

the user.

Putting your ngers in the bowl while the mixer is

running may cause injuries.

InstallatIon of new mIxer:

Installation and securing:

If the mixer is placed on a table, it must be bolted on to the

table. Use 4 M6 bolts with a length of 90 mm + the thickness

of the table top, see drawing page 10

If the mixer is placed on a bench stand, it can be placed

direct on the oor. Foundation bolts in the oor are recom-

mended. Intermediate pieces can be inserted under the

mixer’s feet, if the oor is not completely even.

Connection to power:

Check that the voltage and frequency printed on the

machine sign is correct compared to the place of in-

stallation. The machine sign is placed at the top of the

back of the mixer.

When the mixer is connected, use phase + neutral + earth

or phase + phase + earth. In both cases it is important that

the voltage between the two live pins is in accordance with

the machine sign. (See examples on page 3).

The mixer must be connected

to earth!

If not, it will cause missing function of EMC

lter as well as risk of damaging the frequency

converter.

• The mixer must only be connected to single phase power

with earth.

• A two-pin plug with earth is to be used. Alternatively two

conductors and earth from a 3-phase power supply.

• The mixer must be protected by a differential switch.

•

The machine is secured through a 5A fuse. The fuse is built

into the cable plug which is placed at the bottom of the back

of the mixer. To this comes a 10A fuse which is mounted in the

frequency converter, see “Service instructions” page 10

General: ......................................................................................................................................................................2

safety: ......................................................................................................................................................................2

InstallatIon of new mIxer: ................................................................................................................................................. 2

examples of power ConneCtIons: ...................................................................................................................................... 3

Vl2 Control panel - surVey of VarIous operatInG sItuatIons: ............................................................................................ 3

operatIon of the mIxer: .................................................................................................................................................... 4

the remIx funCtIon: .......................................................................................................................................................... 5

ChanGe of fIxed speeds: ...................................................................................................................................................5

reset of tImer: ................................................................................................................................................................. 5

oVerload: ......................................................................................................................................................................5

proCedure In Case of oVerload: ....................................................................................................................................... 5

reCommended maxImum speeds: .......................................................................................................................................... 5

ConstruCtIon of the mIxer: ............................................................................................................................................... 6

the maxImum CapaCIty of the mIxer: ................................................................................................................................... 6

CorreCt use of tools: ...................................................................................................................................................... 7

CleanInG: ......................................................................................................................................................................7

maIntenanCe and lubrICatIon: ........................................................................................................................................... 7

attaChment drIVe: ............................................................................................................................................................. 7

reCommended max. speeds for attaChment drIVe: .............................................................................................................. 7

dImensIon sketChes: .......................................................................................................................................................... 7

Vl-2 Control, error Codes and possIble solutIons: ......................................................................................................... 8

test proGrams: ................................................................................................................................................................ 9

serVICe InstruCtIons: ...................................................................................................................................................... 10

CablInG dIaGram: ............................................................................................................................................................ 14

eleCtrICal dIaGram: ........................................................................................................................................................ 15

handle for bowl lIft Can be mounted In both sIdes of the mIxer: .................................................................................... 16

1 2 3 4 5 6 7 ... 19 20

Comments to this Manuals

No comments

Wodschow RN10 VL-2 Operations Instructions Page 2

Comments to this Manuals

Related products and manuals for Small kitchen appliances Wodschow RN10 VL-2